Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not undervalue the forklift at work. If the operation is not good, there will be severe crashes in minutes, and there are many accidents including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that hinder the safety and security of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the driver must first verify that the load is steady and reputable.
4. The beginning needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the work site or while driving, beware that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the car to lose side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain security distance from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or packing. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the Electric Forklift Truck for Warehouse brake. .
4. The speed of the lorry ought to be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the tons does not glide in reverse. The mast can be slanted ahead slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at high speed and hit difficult things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be examined, and gas, lubing oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not enabled.
2. It is not permitted to lift the goods for long distance driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the exact Stand-on Electric Pallet Stacker same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844